Epoxy Flooring Services in Fort Lauderdale
Fort Lauderdale floors live close to the water. Canal lots off Las Olas, boatyards near the port, condo garages a block from the beach, warehouses around the airport. Each one asks something different of a coating, and most of that difference shows up in the prep. We’re a firefighter-owned Miami crew, and Broward is part of our regular run.
Las Olas and the canal-front garages
Fort Lauderdale didn’t get called the Venice of America by accident. A lot of the city’s houses sit on finger islands and canal lots, from the Las Olas Isles over to Rio Vista and the streets behind the beach. Great place to keep a boat. Hard place to keep a garage slab dry.
The water table sits close to the surface on those lots, and a slab poured at grade pulls moisture up from below all year. You can’t see it on bare concrete. Put a coating over it without checking and that vapor pushes against the underside of the film until it lets go, usually as blisters or soft spots near the door. So the first thing we do on a canal-front garage is test the slab for moisture vapor, before anybody talks colors.
If the reading is high, the answer is in the primer: a moisture-tolerant base coat that locks the slab down before the build coats go on. If it’s fine, we go straight to grinding. Either way the slab gets diamond ground to an open profile so the epoxy bites into concrete instead of sitting on dust and whatever the last owner rolled on.
King tides and summer storms push salt water into the streets on some of these islands. A sealed floor keeps that water on top, where a hose takes care of it. Flake is usually the right pick for a canal-front garage, for the grip and for how well it hides tracked-in sand. The full rundown is on our Fort Lauderdale garage epoxy page.
Where in the city changes the job
Port Everglades and the marine trade
Boatyards, repair shops and storage buildings near the port and along the river. Fuel, solvents, bottom paint dust and a hose at the end of every day. These floors get chemical-resistant systems with a texture that grips wet.
Victoria Park and the older streets
Older homes east of downtown often sit on slabs with no vapor barrier underneath, old paint on top and cracks that go back decades. Prep runs longer on these, and we tell you that before we start.
Condo garages by the beach
Storage rooms, private garages and ground-level parking along the beach and the Intracoastal. Scheduled through management, phased so residents can still reach their cars, and ventilated, because an enclosed garage holds odor.
The airport commercial corridor
Warehouses, auto service bays and fleet space around the airport. Forklifts, steel wheels, oil and hot tires. Thickness and joint treatment matter far more here than color does.
Port, airport and floors that earn a living
Around the port and down the river, the boatyards, engine shops and dry storage buildings deal with chemistry. Fuel, hydraulic fluid, solvents, two-part paints and the cleaners used to get them up, then a washdown across the whole floor at closing, often carrying salt. We build those floors around chemical resistance first and grip second: a broadcast quartz or aggregate locked under the topcoat, so a wet floor with a film of oil on it still holds a boot. Where hot washdown or big temperature swings are part of the work, urethane cement handles that better than a standard epoxy.
Out by the airport, the warehouses and fleet bays deal with load. Pallet jacks on steel wheels, forklifts, racking legs that put a lot of weight on a small footprint, and vehicles parking on tires that just came off a hot road. Hot tires soften a thin or under-cured coating and pull it up in tire-shaped patches, so the build has to be thick enough and fully cured before the first car rolls on. Control joints get filled with a flexible material and treated as joints. Coat straight over one and the crack reappears in the new floor before long.
Most businesses can’t close for a week, so commercial work on either side of town usually goes in after hours or over a weekend, phased so part of the floor stays in use. Scheduling and specs are covered on our commercial epoxy in Fort Lauderdale page.
Which system goes where
Every system below is available anywhere in Fort Lauderdale and across Broward County. Which one fits depends on the room, the sun and what gets spilled on it.
Flaked Epoxy
A good fit for canal-front and Victoria Park garages. Vinyl chips broadcast into 100% solids epoxy and sealed under a clear topcoat. Hides sand and tire marks and gives a little texture underfoot. More on the Fort Lauderdale flake page.
Metallic Epoxy
Poured and worked by hand, so no two floors match. Suits a Las Olas showroom, a lobby or a living space where the floor is meant to be looked at. See metallic floors in Fort Lauderdale.
Commercial Epoxy
Built for the port and airport side of town: chemical exposure, daily washdown and heavy wheels. Thickness and texture get matched to what actually runs across the floor.
Grind & Seal, Quartz, Urethane Cement
Grind and seal when you want concrete to look like concrete. Quartz where a kitchen or a marine bay needs grip. Urethane cement where heat and harsh chemicals rule out the rest.
What Fort Lauderdale owners ask first
The questions that come up most on walk-throughs around town.
01Do you come up from Miami for Fort Lauderdale jobs?
02My house is on a canal. Will moisture under the slab lift the coating?
03Can you coat a boatyard or marine shop floor near the port?
04Our condo association wants the garage storage rooms done. How does that work?
05Will an older Victoria Park garage slab take a coating?
06Can you do a Las Olas storefront or showroom without closing us?
In their own words
“Unbelievable work. Got my garage floor done by Zach from 343 epoxy. Him and his whole team were very professional and punctual. They helped bring my vision to life.”
“Best Epoxy Guy in the business. Transformed my commercial property. Definitely recommend him look no where else.”
“Excellent quality!!! Very reliable and friendly guys with a great product. They were Punctual and were done within the time frame we were given. We love supporting our local first responders any way we can. My wife and I love our new floors. Looking forward to enjoying it for years to come.”
Tell us what the floor
has to handle
Call and tell us where the slab is and what goes across it. We’ll come out, test it, and put a fixed number in writing.
Want the number before anything else?
Every Fort Lauderdale floor gets a fixed written price before work starts, with prep and finish on separate lines.